Extreme Paints Industrial-Grade Polyurethane Floor Paint 20.0 kg

Extreme Paints Industrial-Grade Polyurethane Floor Paint is a heavy-duty, solvent-based floor coating specially engineered for tough industrial environments such as factories, warehouses, workshops, and high-traffic garage floors. This single-pack PU floor paint forms a durable, oil-resistant, and chemical-resistant surface that holds up against forklift traffic, tyre abrasion, impacts, and wear.

The anti-slip polyurethane variant is pre-mixed with fine silica particles, adding surface texture for improved traction on ramps and wet floors—ideal for loading docks and commercial kitchens. Easier to apply than two-part epoxies, this solvent-based polyurethane coating levels smoothly and delivers a long-lasting, high-gloss finish.

Manufactured in the UK under ISO 9001 QA protocols, each batch is viscosity-checked to ensure color consistency and coverage. Always in stock for rapid dispatch - perfect for time-sensitive projects where large industrial floor areas need immediate coating.

Suitable Substrates

• Bare or sealed concrete (must be dry and properly prepared)
  

• Ground power-floated or polished concrete
  

• Prepared metal surfaces
  

• Sound timber floors
  

• Most porous masonry surfaces
  

Note: Avoid using on self-leveling screeds unless tested - most are non-porous and not ideal for solvent-based PU coatings.

Primer Required: Apply Extreme Paints Clear Polyurethane Primer & Sealer to bare, porous, or mechanically ground concrete for optimal adhesion and penetration.

Available Colours

• Black
  

• Dark Grey
  

• Grey
  

• Light Grey
  

• Mid-Green
  

• Dark Green
  

• Post Office Red
  

• Red
  

• JCB Yellow
  

• Orange
  

• Blue
  

• White
  

Custom RAL or BS shades are available on orders of≥ 100 litres.

Coverage & Spread Rate

• 5–7 m² per liter per coat (varies by surface porosity)
  

• 5 L tin ≈ 15 m² (2 coats)
  

• 20 L tin ≈ 60 m² (2 coats)
  

Drying & Curing Times (@ 18 °C)

• Touch dry: 6–8 hours
  

• Recoat: 6–8 hours
  

• Light foot traffic: 24 hours
  

• Forklift/vehicle use: 72 hours
  

• Full cure (chemical resistance): 7 days
  
  

 Storage & Thinning

• Store between 5 °C and 30 °C in sealed containers
  

• Use white spirit or PU thinner (≤ 5%) for spray application
  

• Order the total required volume in a single batch to ensure color consistency
  
  

Application Instructions

1. Surface Preparation

• Remove all loose paint, grease, dust, or debris
  

• Substrate moisture should be below 4%
  

• Mechanically grind power-floated concrete
  

• Avoid painting over damp surfaces
  

2. Priming

• Use Extreme Paints Polyurethane Primer & Sealer on bare, porous or brittle concrete
  

3. Mixing

• Stir thoroughly for 3 minutes with a paddle mixer
  

• For the anti-slip version, ensure silica grit is evenly dispersed
  

4. Application Method

• Brush or roller for both finishes
  

• Airless or HVLP spray for a smooth gloss finish only
  

• Do not spray the anti-slip variant—grit will clog nozzles
  

• Apply two thin coats at right angles for the best coverage
  

5. Curing

• Wait 6–8 hours between coats
  

• Allow 24 hours for foot traffic
  

• Forklift-safe after 72 hours
  

Fully cured, chemical-resistant surface in 7 days

Safety Disclaimer:
This is a solvent-based, flammable floor paint intended for industrial and professional use only. Use in well-ventilated areas and keep away from heat, sparks, and open flames. Avoid inhaling vapours and prolonged skin contact—always wear suitable gloves and eye protection. Store securely and out of reach of children. Dispose of any waste in accordance with local regulations. For full safety information, consult the product’s Safety Data Sheet (SDS)